Search for: All records

Abstract Due to the ubiquity of textiles in the lives, electronic textiles (E‐textiles) have emerged as a future technology capable of addressing a myriad of challenges from mixed reality interfaces, on‐garment climate control, patient diagnostics, and interactive athletic wear. However, providing sufficient electrical power in a textile form factor has remained elusive. To address this issue, different approaches are discussed, starting with supercapacitors' advantages and limitations and material choices for textile‐based supercapacitors before discussing proper data analysis and design considerations of textile‐based energy storage to power wearable electronics. 

Abstract Polyvinylidene fluoride (PVDF) is a semicrystalline polymer used in thin‐film dielectric capacitors because of its inherently high dielectric constant and low loss tangent. Its dielectric constant can be increased by the formation and alignment of its β‐phase crystalline structure, which can be facilitated by 2D nanofillers. 2D carbides and nitrides, MXenes, are promising candidates due to their notable dielectric permittivity and ability to increase interfacial polarization. Still, their mixing is challenging due to weak interfacial interactions and poor dispersibility of MXenes in PVDF. This work explores a novel method for delaminating Ti₃C₂T_xMXene directly into organic solvents while maintaining flake size and quality, as well as the use of a non‐solvent‐induced phase separation method for producing both dense and porous PVDF‐MXene composite films. A deeper understanding of dielectric behavior in these composites is reached by examining MXenes with both mixed and pure chlorine terminations in PVDF matrices. Thin‐film capacitors fabricated from these composites display ultrahigh discharge energy density, exceeding 45 J cm⁻³with 95% efficiency. The PVDF‐MXene composites are also processed using a green and sustainable solvent, propylene carbonate. 

Abstract The origin of MXene's excellent electromagnetic shielding performance is not fully understood. MXene films, despite being inhomogeneous at the nanometer scale, are often treated as if they are compared to bulk conductors. It is reasonable to wonder if the treatment of MXene as a homogeneous material remains valid at very small film thickness and if it depends on the interlayer spacing. The goal of the present work is to test if the homogeneous material model is applicable to nanometer‐thin Ti₃C₂T_xMXene films and, if so, to investigate how the model parameters may depend on variations in MXene interlayer spacings. MXene films containing flakes with interlayer spacing between 1.9 and 5.5 Å have been prepared using various intercalating agents. It is shown that modeling the films as being homogeneous agrees with experimental tests in the microwave frequency range. Microwave conductivity and dielectric constant parameters are estimated for the homogeneous film model by fitting measured results. The direct current (DC) conductivity matches the estimated microwave conductivity on the order of magnitude. A highly effective dielectric constant provides a good fit for the lower conductivity MXene films. Optical absorption agrees with the homogeneous material model of thin films as well. 

Abstract MXenes are promising passive components that enable lithium‐sulfur batteries (LSBs) by effectively trapping lithium polysulfides (LiPSs) and facilitating surface‐mediated redox reactions. Despite numerous studies highlighting the potential of MXenes in LSBs, there are no systematic studies of MXenes’ composition influence on polysulfide adsorption, which is foundational to their applications in LSB. Here, a comprehensive investigation of LiPS adsorption on seven MXenes with varying chemistries (Ti₂CT_x, Ti₃C₂T_x, Ti₃CNT_x, Mo₂TiC₂T_x, V₂CT_x, Nb₂CT_x, and Nb₄C₃T_x), utilizing optical and analytical spectroscopic methods is performed. This work reports on the influence of polysulfide concentration, interaction time, and MXenes’ chemistry (transition metal layer, carbide and carbonitride inner layer, surface terminations and structure) on the amount of adsorbed LiPSs and the adsorption mechanism. These findings reveal the formation of insoluble thiosulfate and polythionate complex species on the surfaces of all tested MXenes. Furthermore, the selective adsorption of lithium and sulfur, and the extent of conversion of the adsorbed species on MXenes varied based on their chemistry. For instance, Ti₂CT_xexhibits a strong tendency to adsorb lithium ions, while Mo₂TiC₂T_xis effective in trapping sulfur by forming long‐chain polythionates. The latter demonstrates a significant conversion of intermediate polysulfides into low‐order species. This study offers valuable guidance for the informed selection of MXenes in various functional components benefiting the future development of high‐performance LSBs.